Search results for query: *

yep , thanks we got the job done.. another trick is to disconnect the differential lock shifter mecanism , that way the lock gear is just tight enough to stay put, aligned with the differntial , when you slide in the new shaft with the portal, into postion.other wise its falling all over the...

ok problem resolved.... the half shaft is broken.....because the bolts from the hub slaskened thee was too much presure on the axle and it sheared just after the splines.

ok new info, for our internet mechanics...... the left side rear wheel had most of the 12 bolts holding it on slack by a good 1.5 cm,at the bottm less so at the top. so much so that one bolt broke . So now the the tractor will move if I press on the diferential lock, and hold it down...

hi ya Renze.... well today I put the tractor in 2nd gear, and then started the engine, the engine purred like a lion and I did not jump forward. the pto is functional the 3 point hoist works fine. with the engine running ,I press on the clutch, all the gears engage with out noise , the high...

ok ... when the clutch is pressed down I can switch to all the gears including high low gear selector. but with the engine running if I try to push the gear stick to a gear , without pressing down on the clutch, the gears grind....

please explain more details, can I see that spring from the ouside of the tracto,r via the square hole on the side of the tractor housing? as before mentioned I can shift to all the gears, including high and low the gears engage fine, bur when I release the clutch nothing happens, the clutch...

ok guys been awhile, but now I have a new problem. I was slowly backing up when suddenly the clutch disenaged, and I was in neutral. I can shift to all the gears easly enough, and can move from high to low too. but after releashing the clutch there is no forward or reverse movement. the...

:D ok Mike thank you,....... you wouldn't happen to have a part number for the relief vavle ?

:) ok I have no rear hoist lift, when the 400 lbs, snow blower is attached to the hoist( it tries to move up but it lacks the strengh to do so), of my 5011 . If I remove the blower the hoist will raise. I have plugged a pressure gauge, in the output for the outer circuit hydrolics and it...

maybe the saftey pin has broken I pop one now and again when the shoot gets frozen to the base.

oil level is ok but under the tractor seat is the magnetic oil filter, this has not been cleaned for quite some time because the tractor cabin is blocking the with drawl of this filter. the cabin is sitting about a half centimer too close to the filter to unscrew it I have had the tractor for...

the outer circuit works a cylinder to lift a scraper in front of tractor , the lift behind does not lift, which means the two control handles on the right beside the seat dont work, the two close to the wheel

no levers betwen the legs just the high low on the right side heel of yer boot, and the pto engage lever behind the left boot as you sit in the chair I will check the magnetic filter under the seat and check to see I have enough oil in it today in about 15 hours from now

ok the rear lift and the outer circuit no longer function...... what do you supose is the problem? I know I have oil pressure because an outer circuit which is independant, from the control system under the seat, is functional. this is a zetor 5011

nice pic I will post one of my tractor,lots of snow eh, we got 35 cm with the storm on dec 16/17

hiya good place for all your questions. parler vous francais je suis de quebec aussi,

What oil should we be using in injection pump and governor for a 5011?

replying to part of my question the oil pressure should be at .o5MPa at idle speed and at operating speed should be 0.2 divided by 0.5mpa..... .4

hi ya guys and girls, I have a 5011 , I would like to check the oil pressure because the oil pressure light comes on when Idle is below 1100 rpm. what should the pressure be at if I check the pressure and when can I check it . ..... wonders where the pressure sensor is located, maybe...

cool nice to know that