Search results for query: *

Hi guys, looking at upgrading the 7745 to a 2011 9040HS. It has 1300 hours, cab, mechanical shuttle, A/C, 4x4, self levelling loader and is in great shape. Not much to compare it to though, from what I understand it's a rebadged Proxima for sale in Canada. So Proxima 100 or 95? The 9040 is...

Anywho, we're back in business. Previous owner drilled and tapped into the pump plate to feed control block for the loader and rear remotes and the then piped the continuous flow through said block back into the pump plate to feed interior steel line. So that plug was in between the exit and...

Inside the tractor yeah, one line, but I was referring to the lines on the exterior of the pump plate that feed the hydraulic control valve for the loader and rear remotes.

Looking at it further it appears the plug may have been used to divert some flow or that was the intention?? Pressure outlet out of the pump after overload valve has an exterior half inch street elbow threaded into the bottom of the plate with a hose going to the "block" under the tractor, the...

Hey guys, finally got the pump down and where there is a small pipe sticking up around the edge of the base with 2 O rings on it I saw something almost totally blocking the hole down below? I took the end piece off where the external hose attaches and there was a half inch threaded plug? Now...

Hey Mike, thanks for reply, hmm I'm having a tough time picturing where those "O" rings are. I replaced two on the pipes.

No we didn't change the relief valve because our neighbor has the identical tractor with identical problems a few years ago and all he did was change the pump and he was back in business. I should have listened to my gut and replaced the valve too, ah well, not a hard job to drop the oil and...

Hey Mike, Yeah first thing, cleaned magnet and mesh filter.

Hello again everyone, 3 point hitch very slow, loader very slow, opening round baler off the rear remotes very slow/weak. So we changed out the hydraulic pump, we also replaced the 2 "O" rings in there got it all together and everything seems the same>:-(. Any input would be appreciated. Thanks

Thanks Renze for the quick reply.

Hello, it's time for a new pump (which was purchased). Looking for some input or diagrams as to what else is needed. Doesn't look like it will too difficult, drop the round plate underneath, is the pump attached to the plate? Will I need "O" rings or anything, probably a new gasket for the...

Got her all back together and running smooth as ice. It even holds oil now:p.

Yeah got the hub off and disassembled, big inner bearing has completely, and I mean completely failed and 4 or 5 rollers have disappeared, crunch crunch. Thankfully everything else looks fine, but I will be changing both bearings and seals obviously. Planetary gear looks fine.

Thanks for the reply, going in a straight line in 2 wheel drive is when it started. So I think I start by removing the "hub cap" held on by 3 flat head bolts? There is also 12 bolts around the outside of the rim?

Hello everyone, looking for assistance please. Was out baling this afternoon when the tractor seemed like it was under some abnormal load or resistance (not from the baler) and then the right front tire locked up and then let loose with a loud bang. That was the end of baling, I brought her...

I was thinking maybe it is. The temp gauge comes up to the beginning of the green, but the rad cap can be removed with no pressure build up and I can't really see any fluid movement in the rad while running?

Maybe it's a sluggish thermostat?

Hello again, I'm having a coolant flow problem on the tractor. The bottom rad hose stays cool to the touch after it's up to temp. Top of rad, manifold to heads and heater loop are all hot. New pump, new thermostat, new head gaskets and new rad cap but it still appears to not flow. Just...

thanks for the quick response Al! So to clarify, by 1&2, you mean the cylinder closest to the rad and work left to right? Also, this method allows you to do both valves per head at a time? Sorry, it's my first time doing this and I just want to get it right. Thanks again

Hello all As the title suggests I just installed 4 new head gaskets and it's time to set the valve play. I know the clearance is 0.010-0.012 in. but I'm totally lost on how to do it. I have a feeler gauge but the sequence of setting things up eludes me. If someone has paperwork or can give me...