Search results for query: *

Ive had problems with the steering of my 6245 for as long as I have had it. Yesterday I broke the rod end that connects to the steering cylinder and now have no steering at all. Instead of spending a lot of money reconditioning the steering and still have mediocre power assisted steering I am...

Mine does the same thing. I am on the verge of ordering replacement parts (inner circuit control linkage and the rod it pivots on) to see if that rectifies the problem. keep us posted with how you go. Paul.

I used the oil drain hole on the rear axle of my 6245 for the return line of the loader and took the pressure from the plug on the pump plate on the bottom of the rear axle as well. You have to have the remote lever locked either fully forward or backward to get pressure at that point, but it...

In my limited experience with my 6245, I have had the following issues: There is a pipe that runs through the diff housing between the pump plate and the top housing, this is sealed with o rings, mine got old and brittle and failed causing a loss of pressure. My lift cylinder seals were damaged...

Just don't pay for it ;D Sounds like you are having similar issues to me with my 6245. I have yet to get mine sorted out but have found a few other problems along the way. I'm at work now but I'll post some suggestions when I get home.

[url=http://www.website.com]http://www.ibeno.cz/ukindex.htm[/]

I think I would be going somewhere other than the dealer! It's not a warranty issue so anyone can do the job. Perhaps ask around locally for a mobile tractor mechanic that will visit you? I suspect the brake issue will be hydraulic as well, if it reoccurs replace the master cylinders and think...

I had the same issue on my 6245 when I bought it. I just filed enough off the flanges of the ball on one end of a Bareco top link so it would fit. In my case the very top hole for the pin is cat 2 on one side and cat 1 on the other which is a bit odd, all the holes below are cat 2. Hope that...

I did see that, but couldn't see how it adjusted as there didn't appear to be a slot to alow for movement. I'll have another look though, thanks. I also tried taking the lever off the shaft to rotate it on the spline, but the spline is indexed so no joy there. Give it a couple of weeks untill I...

The whole manual is like that, but once you actually have a go with the tractor in front of you, it's not too bad.

Tried both those things. It's amazing how complicated the manual makes a simple procedure sound! I got a little more travel but when I put the quadrant lever cover back on what I gained was lost as it limits the travel of the inner circuit leaver somewhat. Thanks for the suggestions though, keep...

I wish it were that simple, but in my case unfortunately not. I am not getting full travel at the upper arms, probably only about half to two thirds. Definately something wrong with the hydraulic distributor or the mechanism that controls it. I did find what looks like a steel pin or plug of...

Bump Thoughts anyone?

Down is engaged on my 6245.

Yes there is a spring between the two halves. To give you a bit of back ground, the tpl has never worked correctly on this tractor. When I bought it, there was no controll at all, so I removed the hydraulic cover and replaced all the o-rings in the hydraulic distributor and the seals in both...

Can anyone that has had thier hydraulic distributor apart recently varifyed that the inner circuit spool valve from my 6245 in the picture below is assembled correctly? I am having trouble with my 3pl and as best as I can tell from the workshop manual and parts book, that is correct but I am not...

Found them. Thanks. I was looking in eBay Australia:)

Hi Mike. Thanks for the heads up on that. Unfortunately I haven't had much luck finding the brackets you mentioned on eBay. I don't suppose you could post a link? Thanks. Paul.

Hi Renze. I know this is an old thread, but if you still have the cad files for the loader brackets I would be interested in a copy as well. Thanks :) Paul. paul at shurvell dot com

Hi all. I am considering fitting a front loader to my 6245 and was wondering if any one could send me some pictures of the mounts and mounting points on a tractor from the same series? I can't afford to buy a new loader at the moment so I am thinking of modifying a second hand loader to fit and...