Search results for query: *

Also, is there any type of cover or access plate I can take off and look in there first? I hate to take all that stuff off and it not be the problem. Thanks and Happy New Year to all!

Ok, thanks Renze. I'm assuming I have to take the cab off to do this?

Not sure if you have fixed this yet or not but I had a similar problem with ours. I had to drain the brake fluid and replace it with hydraulic fluid. It works fine now until it gets really cold(10F) and then it still works but is hard to push. I'm sure there are plenty of reasons I should not...

Hello all and Merry Christmas! I have a 7745 that the pto and hydraulics just stopped working all at once. I took the gearbox cover off and it appears all the forks are ok. I did notice that the gear in the first section of the box will move back and forth about 16-20mm and this seems...

Hello all, I have a 7745 that the pto and hydraulics have stopped working. From what I've read here, and already tried, my next step is to pull the top trans cover. Is there a certain process for this? Shift levers need to be in a certain position or anything like that that I should know...

Sorry for the late update but this was the screen in the sump was plugged with gunk. Thanks for the help.

Yes, I did check those. Even tried putting it in 1000rpm side, but still nothing. Normally, you can hear it whining(probably the relief valve, but not sure) but now I can only hear it a little bit when I raise the lever for the 3pt arms.

No, its not milky.

I have a 7745 that the hydraulics stopped working on. I have always used the 80/90wt oil in it and had no problems even in cold weather. Nite before last I checked it and was a little low so I added a gallon. Next morning(20 deg F) and now no hydraulics at all. This is very thick oil for this...

I was getting ready to use my 7745 to spread fertilizer this morning and when figuring the settings found that it does not have a mph or km/h chart in it. Does anyone have one they could share with me? Any help is greatly appreciated. P.S. - I am in the US, dont know if that makes any differece...

I have been running about 20%WVO (filtered only) with tractor diesel in my 7745. Summertime only though. I'm sure there is probably some reason that you need to go through the washing steps, but at this low mixture, it seems to be working OK. I do not recommend using it in a tractor that you are...

If its 4wd, my book says no toe in, should be straight.

Thanks also to you Mikael.

Thank you forterra for the great advice. It is very much appreciated.

I have a 7745 and am trying to figure out how to check the fluid level for the front axle gear box as well as the planetary drives. I have found the plugs on the planetary drives but am not sure what position they are to be in when checking the fluid. I also found two plugs on the axle housing...

I am thinking about adding a thermostart unit to my 7745 and was wondering if anyone else had done this before. I am not sure how to get fuel to this and if it has to be pressurized, etc. I thought maybe there was somewhere I could tap into the injection pump ? Any ideas would be great...

Can you tell me if the 4wd stays engaged in high range on my 7745 or only in low range ? It has the 5 x 2 gearbox. See my last post on noisy transmission. Thanks, juney

Thanks guys ! Sounds like the air tank would be more trouble than its worth. I need to try it at the higher rpm's as it was just a little above idle when i tried it before. Another question for ya - Yesterday I was putting out a round bale and when I tried to go up on the pile in 6th gear (mine...

I had tried pumping up a tire with it just to see how it worked and it seemed very slow. So I was thinking that if I had a air tank to hold a reserve amount in, then when I needed to pump a tire or blow something out I would have a supply. Maybe this is not a good idea. This is the first tractor...

What psi or bar should this relief valve be set at ?