Search results for query: *

Solved the problem of the clutch needing to be bleed, and the fluid reservoir requires filling ! The clutch slave cylinder O-Rings were marked (grooved) such that there was a poor seal. Now that it is warm at night (0 Degree C) there is no problem. However, I have replaced the complete slave...

On cold mornings, -25 Deg C or lower I am finding my clutch needs bleeding, and the fluid reservoir requires filling. I have replaced the two hoses from the reservoir to the clutch, and brake master cylinders. I have replaced the line from the clutch master cylinder to the clutch slave. I can...

We have had a couple days around zero degrees C in the valley, and I took the opportunity to tighten all connections starting at the generator,the starter, the voltage regulator, and the fuse boxes. The problem went away when I took the fuses out of the small fuse panel, and squeezed the...

I have a 7245 with a Bk6011 Cab [the cab was manufactured in 1986]. I have an electrical diagram for a 7245 (acquired from Dave Peters, a member of this forum). I am now looking for an electrical diagram for the cab. Occasionally I lose all power to the front mounted cab lights, fan motors...

I can engage the PTO, and it will rotate, its RPM increasing as engine RPM increases. However, under load, it slows down, may stop completely, and without any action on my part start to rotate again (it is as if the clutch is slipping) Any ideas as to where to start to solve this issue, which...

Solved the problem today: Unable to find any leaks using pressure test method described in "Zetor UR1" Dealer Service Manual section c page, c-2. Last line in the manual states (Section C , page c-2 ) that there should be a beather hole in the "white surface" of the fuel tank cap. Mine is...

I have a 7245, built in 1989, which I use to move snow in the winter , and odd jobs (grading driveways, moving gravel, etc.) in the spring ,summer, and fall. Just recently, I must always prime the fuel system before attempting to start the diesel engine (for the first time each day it is used)...

My brake fluid level is up, the left brake works perfect, i.e. press in the LH brake pedal, and the left wheel stops rotating, release the LH brake pedal and you can rotate tire manually. However, the RH brake pedal does not have the same effect on the right wheel. Press the RH brake pedal to...

I am installing the steering damper on my 7245, the manual states "ISO VG 15" when changing oil abroad (I assume North America) Any suggestions as to what I should use in North America ? Thanks in advance

I have a 7245, engine serial number is 37830, and the console tachometer correctly displays the engine RPM, but the hour meter does not clock any hours. I have determined from reading responses to a previous question on this topic that I should replace the tachometer sending unit! My parts...

What clock ? The tachometer, is showing engine RPMs - thus should I not assume the sensor (or revolution counter is functioning)? Where do I find the clock on the tractor, and in the parts catalog ? Thanks in advance, Valley7245

My poor description of what I found may have lead us off course. The reduction hubs, both LH and RH are lubricated with SAE 80W90 gear oil - althought I did have to top up the RH one this spring. What I see in both the shafts of the LH and RH bleeder caps is a grease type substance that at...

Thanks for the tip DaveP, and Rentze. I removed part #6745-3267, it appears to be a breather cap, that was very dirty. Cleaned it up (soaked in some diesel fuel, used compressed air to blow it clean). The shaft was full of grease, and the part of the front wheel support that it screwed into is...

If my tachometer works, and my hour meter does not clock any hours . I have determined from reading responses that I should replace part number 5911 5725 if I have three wire system (works with "non electronic tachometer"), or part number 6245 5708 if I have a two wire system (works with...

Two part question If I look at a 7245 front wheel Drive diagram, there is a part identified as # 10, it is called a "Bleeder Cap" (part # 6745-3267), what does it bleed, does it come off ? Also, the inside of the right front drive wheel disk (side closest to tractor body) over the winter has...

Thanks Dave P for the quick response

What is the diameter of the "Brake System Bleeding Hose", part number 6911-8551. I know I can get a piece of clear plastic hose, if I only knew the diameter. Thanks in advance, Valley 7245.

Where would I get a copy of the 7245 electrical wiring diagram (in Canada), given I have several wires in that have been perviously disconnected - and I would like to get things working ? Thanks in advance, Valley 7245

I acquired a 7245 in 2005 November, engine serial number is 037830, tractor serial number is 024896 Tractor has a BK6011S(numbers could be wrong , could be BK60115?) cab on it. Indications are the cab was made in 1986 ? What year would this tractor have been produced / Thanks in advance...