Search results for query: *

Hi everyone, I'm looking for a steel bonnet to fit a 3045 (the round bull nose type). Can these be got anywhere? or is there any alternatives? Thanks Sean

Hi all, I want to lift the lid on my 3045 gearbox is there anything I need to do before I proceed for example do I need to remove the adjusters at the back of the lid between the hi/low and pto selector levers? Many thanks Sean

Hi Steve, I had the same problem with the steering wheel on my 3045. I had to use the pullers to get it off although the end of the shaft wasn't mushroomed like yours. I used 2 legs on the pullers attached to a clamp bolted together below the wheel. Lots of WD40 and a decent pair of pullers. I...

Hi guys, how do i remove the crankshaft pulley from this tractor? is there a special tool for the job? i need to get the timing cover of as it has 3 broken studs in it that hold on the sump. any ideas greatly appreciated sean

Hi Folks, We have just purchased one of the above tractors (1year old and 250 hours) and are well pleased with it. Just one thing however, it is difficult to change gears espically when trying to change down to get in gateways and such. I was wondering if this has to do with the tractor being...

Hi, I got parts from this guy for my 3045 and sent over to N. Ireland for a farily decent price also. www.motocheck.fi Good luck Sean

Hi, I removed my steering wheel using a set of hydraulic bearing pullers. Remove the centre cap and you'll find a castle headed nut remove the split pin and nut. If you can get a set of pullers with a clamp attachment all the better, fit the attachment below the spokes of the steering wheel...

Hi Guys, I been looking for a CV joint for a zetor 3045 for a while and I came across this company in Slovakia who make whole new half shaftscomplete with a new universal joint albeit just a single one but it is good and big allows the full steering lock to be achieved. They also manufacture...

Hi people, Can anyone tell me if it is possible to swap the front axle from a 5455 to a 3045? Thanks Sean

Check your pm Sean

Hi all, I'm looking for a replacement front axle for a zetor 3045/3545 or even parts for said axle. Thanks Sean

Hi, Here's what I'm talking about! http://www.facebook.com/home.php?#!/photo.php?fbid=196677410361234&set=a.196673153694993.54181.100000569303396&theater

Hi Matthew, I have the swivel housing of and now face a CV joint that somebody has butchered at before! Is it possible to get a replacement zetor CV joint? or should I be looking for something about the same size of a more modern piece of kit to replace it? Thanks Sean

Alright prople have nearly completely dismantled the front axle on the 3045 just a couple of questions; The swivel housing at the outside end of the half shaft can it be dismantled? If so how is it done? Also any other advice on this axle would be helpful Cheers Sean

Hi, I need help with the front axle of my 3045 ??? are these axles hard to refurbish? I took the front casing of the diff lock and the bearing fell at my feet in pieces! and there is a lot of play on the driven shaft going into the diff. Is this play unusual? and will it have done damage futher...

little help here guys please{:-(

thanks renze very useful sean

hi all, i was wondering if anybody has an operators manual or parts manual for the above machine:-/ as i need to do some repair work on it 69) cheers sean

hi all, i know this is not the right forum {:-( but i was wondering if anyone has an operators manual for a zetor 5.5 rur manure spreader or even a parts manual.:( any help appreciated;) sean

hi, as most of you know i'm restoring a 3045. i recently changed the transmission oil and cleaned the filter and now when i engage the pto lever full forward the lift arms do not rise but the pto spins ok and the external supply works as well. i'm i missing something simple or is there a fix...