Search results for query: *

I looked at it today, it's too light for the no-till drill. Going to pass.

Hi: I am thinking of selling my Crystal (maybe a mistake). I speak in hushed tones around her, I don't want her to know! Anyhow, I'm looking at a 7745. How can I tell what year it is? I read posts and one said it has turbo problems in the earlier version - that so? I also hear horsepower...

Hmmmm. Seems to me I fiddled with this in the past and backed it out to the point it came right out. It is back in place now but how far can you back them out? I thought their would be a stop. Good to know in is slow out is fast. Thanks.

All has been well with the Zeteroid of late. However, I was no-tilling soybeans in this spring and I have a little hydraulic problem. On my 8011 when you lower the no-till seed drill it drops slow. This is a heavy item 7-8000# and should go down quicker. When you turn on the headland and begin a...

Dave: Presto! it works. Got the info, thanks. Your method on the heater removal is much appreciated too. I haul two wagons 9 tonnes of soybeans 13km to the elevator in the cool to cold fall and do it 8-10 times so a heater is a must. Ken ps I've had this old 8011 for about 5 years and it has...

So the rad core comes out from the top inside the tractor? I tried your link for the axel seal replacement but it didn't work. Ken

Gents: Is there a trick to removing the heater core on a 8011? Looks like they built the tractor around it. Mine leaks and I took a shot at taking it out but gave up. Also, is it a hard job to replace the outer axel seal on the rear wheel ( left one as you sit on the tractor)? Mine leaks down...

Thanks gents for this vital information. It did run hot for a while but is free now. I avoided using the brakes till I got my soybeans off and winter wheat planted. A fellow I know suggested using silicone brake fluid a few years ago. I tried it and it made the brakes work not too bad. However...

My 8011 brakes have worked not too bad since I've owned the tractor. The other day, however, they stuck on, on the left wheel. I had an awful time freeing that wheel. Has anyone any similar experience and any hints on what caused it and why and how to fix it. I've not bothered to use the brake...

I have an weep on the outside of the injector pump where the throttle linkage pivits. If you don't turn off the fuel tap at the tank it has a slow drip to it. It's been that way for a few years. What's to come. Will the pump fail all of a sudden or just weep away for a few more years. I'm...

Yikes it's getting cold! My heater core sprung a leak and I tried to get it out to fix it the other day but gave up. Looks like they built the tractor around the heater core. Does it come out from the bottom or after you take the whole dash panel etc off? Looks like their might be a trick here...

New aftermarket pump in and working fine. A great improvement in lift speed and capacity. No delay when starting tractor. Using TDH fluid. Took a chance with Sparex adaptor kit (had to buy copper washers, not with kit). Measured, cut and brazed ball end on original presssure line from pump. Got...

$335 cdn plus tax, plus adaptor kit $45cnd. The pump is in but not hooked up to tractor steel line. I see the line is rigid and very hard to take off (battery box, battery removal etc) If I did and cut and re-brazed ball end it would have to be exact in length as there is no lateral movement...

Renze: I went for the new pump. Aftermarket from Poland. Of course a little trouble in paradise! 1 the lower pickup turbe from pump to housing was too big on one end so that was a while getting a fit. But, alas, pump is in. 2 Pressure pipe that threads into the new pump won't go in without...

Renze: Thanks for your interest. I pulled the pump and have one on order. I did open it up for a looksee. Lots of side play in the drive shaft and quite a bit of end play on the gears. It must just sit and spin in the oil and have little or no suck and low pressure when it does pick up the...

Anyone use heavier oil than 80-90 to overcome worn hydraulic pump that does not lift when hot?

Hi All: New here and of course have a problem. Here are the symptoms: Upon startup, cold 3pth will not lift. Place nose of tractor down and it will lift (prime?) When worked (ploughing, or no till drill) 3pth lifts slow then will not have power to lift plough (KV 4 furrow). It has light oil...