Search results for query: *

Hi Gareth i had a suire loader on my 7245 but it was realy too heavy for the steering , well it`s now languishing in polland

Hi Don If you look in a previous forum post 6245 extremelly hard to steer left ixer0 tells you how to do it via the ram adjustment .:) Martin

Hi renze I have 16.9 r 30 on the rear do you think they will match with the 12.4 / 24 `s ? , just needed to check that they didn`t get too close to the assister ram either but if you have them as standard they must be ok . Thanks for the help Martin

Thanks for that renze . Has anyone ever tryed putting 12.4 /24 stomil tyres or anyother 12.4 `s on their 7245 ? thanks martin

Hi all HOPE YOU ALL HAD A GREAT CHRISTMAS:) Does anyone know if you can fit 12.4 / 24 stomold tyres on to a 7245 , as a replacement to the 11.2 / 24 that are on there now . it does have a loader on if that makes any difference, any help would be great . thanks martin

Thanks renze , are you saying that the tractor has to be moving and reving at 1000 rpm for the asister ram to work on the steering ? is there anything you can add to the engine to free up the rings thanks martin

Hi , i have changed a large filter today that is in line between the underneath of the back end and the pump at the front , it`s quite big and cost 30 :o. is there still another filter under there that does the back end ? and does anyone else have one with these inline filters in there 7245 ? ...

Hi all just a few questions i would like answers to please 1 . where does the hydraulic filter go , if its underneath i presume you have to drain the oil 2 . does , the asisted steering only work well when you are moving as i have had the pressure checked , replaced the ram , new oil and filter...

Hi , check fuel lines, tank cap,sediment bowl ,lift pump gauze etc and when did you last change the filters ? , sounds like fuel starvation to me . does it start easily ? and what about after its stalled ,will it start again easily ? . :) thanks martin

Hi , remove the hub cap jack up the front wheel and support with a axel stand, then remove split pin and undo the large nut, check the bearing is good and tight and loaded with greese if so replace the bearings and wheel and tighten the nut untill there is a slight bit of top to bottom movement...

Hi , if you remove the nut on the bottom of the 4wd lever and add a slightly larger nut as a spacer then replace the nut this will increace the spring tension and disengage the 4wd ,i had the same on my 7245 and this worked ,also spray a little wd40 on the shaft where it enters the side of the...

Full on the hand throttle and pump till you hear the hissing , sometimes 5 -25 times, works every time with my 7245 ;D ,no hissing no start >:-( , .

Hope you dont mind me joining in but on the question of the pto , why is it when the tractor is in gear with my foot on the clutch and i try and engague the pto using the hand lever there is a growling noise from the area below my feet and the tractor tries to drive forward, with it out of gear...

Thanks for the advice , the pump had no oil in there at all :o , but it didnt stop the hunting :(, there is however air bubles in the plastic conectors to the manifold and the pipe is loose at the manifold , do i need this heater thing ??? or could i remove it altogether untill i can get new...

Hi , thanks for the reply dave , the air filter has been cleaned out already , but the fuel filters have not been changed for years , everything else has been cleaned and changed , its only when put under load that it smokes , and it reves up and down on its own , from tickover to about 1000 rmp...

First time at work today with a spot of harrowing:D,it was going well, (after all the trouble in previous posts) ,went down the hill turned at the bottom and went up ,thats where it started to go a bit wrong:o , the smoke was black all the way to the top ,i couldnt see behind me ,did this sevrel...

Thanks mathew and mike , i replaced the cable from the battery to the bell housing and it started up fine ;D, someone had replaced this with a earth bond from the cab to the starter with 5 mm braded wire that had coroded through inside the sleeving 69 thanks for the help everyone, i started...

Hi , i have tryed cleaning up the terminals on the battery/ the earth on the cab and the solanoid to no avail, it still turns over realy slowly ,there are however two earth leads on the battery , a black one to the cab and a yellow one thats nat connected to anything , is this likely to be the...

Hi mike ,that would make perfect sence as i got a friend to tow it tonight with the intention of just winding over the engine but she fired straight up;D and ran for an hour , all seems ok apart from when i stopped it to try and start again and it was as if the battery was dead , i will try the...

Hi , with all your help i have got the water out , the oil in ,its turning on the starter with the injectors out and i have just put it all together blead up and turned her over, its a bit slow and tight and for some reason on cranking her over there was lots of smoke from the alternator and the...